casa-mp-base

--- configure.bak   2017-04-24 21:04:09.000000000 -0700

+++ configure   2017-04-24 21:55:28.000000000 -0700

@@ -5109,7 +5109,7 @@

 else

    echo "** Could not find the udunits2.h file, udunits support will not be included **"

 fi

-UDUNITS2_LIBNAME=libudunits2.a

+UDUNITS2_LIBNAME=libudunits2.dylib

 # Check whether --with-udunits2_libdir was given.

 if test "${with_udunits2_libdir+set}" = set; then :

@@ -5303,7 +5303,7 @@

 fi

 fi

-UDUNITS2_LIBNAME=`echo $UDUNITS2_LIBNAME | sed s/lib// | sed s/\.a//`

+UDUNITS2_LIBNAME=`echo $UDUNITS2_LIBNAME | sed s/lib// | sed s/\.dylib//`

 UDUNITS2_PRESENT=no

 if test $UDUNITS2_INC_PRESENT = yes; then

    if test x$UDUNITS2_LIBDIR != x; then

@@ -5504,7 +5504,7 @@

    echo "** Could not find the png.h file, so -frames support will not be included  **"

    echo "** Install the PNG library (and development headers) to fix this           **"

 fi

-PNG_LIBNAME=libpng.so

+PNG_LIBNAME=libpng.dylib

 # Check whether --with-png_libdir was given.

 if test "${with_png_libdir+set}" = set; then :

@@ -5698,7 +5698,7 @@

 fi

 fi

-PNG_LIBNAME=`echo $PNG_LIBNAME | sed s/lib// | sed s/\.so//`

+PNG_LIBNAME=`echo $PNG_LIBNAME | sed s/lib// | sed s/\.dylib//`

 PNG_PRESENT=no

 if test $PNG_INC_PRESENT = yes; then

    if test x$PNG_LIBDIR != x; then

@@ -5779,32 +5779,6 @@

 if test x$NETCDF_CC_TEST_SAME = xcc; then

    NETCDF_CC_TEST_SAME=gcc

 fi

-if test x$CC_TEST_SAME != x$NETCDF_CC_TEST_SAME; then

-   echo "======================================================================"

-   echo "Configuration error: You specified that the \"$CC\" C compiler should be"

-   echo "used to build ncview, but the netcdf library was compiled with the \"$NETCDF_CC\""

-   echo "compiler.  Here is the path where I found the netcdf library:"

-   echo "     $NETCDF_LDFLAGS"

-   echo "You must use the same compiler for ncview as was used to build the netcdf library!"

-   echo " "

-   echo "There are two possible ways to fix this."

-   echo " "

-   echo "1) Download the netcdf library and compile it with the $CC compiler,"

-   echo "install it, and try again to build ncview.  NOTE that if you do this,"

-   echo "you might have more than one version of the netcdf library on your system,"

-   echo "built with differnt compilers, which can get confusing.  If you do this,"

-   echo "you will have to specify the path to the (new) version of nc-config"

-   echo "that was compiled using the $CC compiler by configuring ncview in a "

-   echo "way similar to this:"

-   echo " "

-   echo "   ./configure --with-nc-config=/path/to/newly/compiled/nc-config"

-   echo " "

-   echo "2) Configure ncview to use the $NETCDF_CC compiler."

-   echo "To do this, set environmental variable CC to $NETCDF_CC"

-   echo "and run ./configure again"

-   echo "==================================================================="

-   exit -1

-fi

 #----------------------------------------------------------------------------------

 # Construct our RPATH flags.  Idea here is that we have LDFLAGS that might look,